Adventure

CHARACTERISATION OF ALFESI INTERMETALLICS IN 6000 SERIES ALUMINIUM ALLOY EXTRUSIONS

Page navigation Document information Table of contents Similar titles. Claves 4 Estimated H-index: The T6 mechanical properties strength and elongation obtained in this study for rheocast A and A are better than those reported for permanent mould castings of alloy A and A Other Papers By First Author. Are you looking for Intermetallic phase particles in aluminium alloy Archives of materials science and engineering. Attempts have been made to arrest wear of the alloys that experience seizure under the mildest of experimental conditions through the above processing techniques and explain the experimental results through worn surface studies.

Other Papers By First Author. Alloys designed to optimise strength and extrudability have a lower alloy Mg to Si ratio than has commonly been used in AA and AA alloys. Careers and apprenticeships Equal opportunities Vacancies Apprenticeships. British Library Online Contents It is felt that the cumulative effect of the different processing techniques including composite making, ageing and extrusion can open up new avenues for this alloy system, which in general is not used for wear resistant applications. Advanced Search Watchlist Search history Search help.

This paper has provided essential data about various intermetallic phases precipitating in series aluminium alloys.

Electronic books The e-book database EBC. The results show that the precipitation sequence is significantly influenced by the ageing temperature. The solution treatment used in this study was unable to dissolve all of this phase, especially in the 1.

Yao, E T, Chicago, May Chemical composition of the phases was determined by using energy dispersive X-ray analysis EDX.

  990DSL COPPERPROTM SERIES II BROADBAND LOOP TESTER

It is felt that the cumulative effect of the different processing techniques including composite making, ageing and extrusion can open up new avenues for this alloy system, which in general is not used for wear resistant applications. Scientific Data Management Research Staff.

Characterisation of AlFeSi Intermetallics in 6000 Series Aluminium Alloy Extrusions

Influence of the crystallization condition on Al-Si-Cu casting alloys structure. The results showed alfes addition of Ag to alloy A increased the mechanical properties of the alloy.

Kuijpers 5 Estimated H-index: In order to complete extrusiosn confirm obtained results it is recommended to perform further analysis of the series aluminium alloys. This paper proposes the best experimental techniques for analysis of the intermetallic phases occurring in the 6xxx series aluminium alloys, provide wide description of the intermetallics formation through all possible reactions and data about their chemical composition, morphology and crystallography.

Influence of chemical composition variation and heat treatment on microstructure and mechanical properties of 6xxx alloys.

Rheocasting of alloys A and A was investigated in this study. Results for Al-Mg-Si-Fe alloys with 0. The effect of intermetallics on the fracture mechanism in AlSi1MgMn alloy.

Other Papers By First Author. Transtec Publications ; Dense precipitation of various intermetallic compounds is a common feature in the microstructure of Al-Si piston alloys.

Characterisation of AlFeSi Intermetallics in Series – Technische Informationsbibliothek (TIB)

In this study, several methods were used such as: Microstructure and mechanical properties of the Al-Ti alloy with calcium addition. Claves 4 Estimated H-index: Marioara 2 Estimated H-index: The volume loss and wear rate under different experimental conditions were compared between the following conditions for both the alloy and composite i cast ii aged iii extruded. Intermetallic phases have an impact on alloy design since they tie up some of the Mg and Si alloy content.

  MOSALSAL FATMA EN ARABE EPISODE 81

Services for libraries National interlibrary loan International interlibrary loan. This resulted in slightly decreased mechanical properties compared to the 0. Journal of achievements in materials and manufacturing engineering.

Alloys designed to optimise strength and extrudability have a lower alloy Mg to Si ratio than has commonly been used in AA and AA alloys.

Characterisation of AlFeSi Intermetallics in Series Aluminium Alloy Extrusions

Conical bars with different silver contents were produced using CSIR rheoprocess technology, together with high pressure eextrusions casting.

Or are you looking for… Crystallography, Intermetallic, Microstructure. Manufacturing of aluminium matrix composite materials reinforced by Al2O3 particles. Influence of heat treatment on the microstructure and mechanical properties of and aluminium alloys Journal of Materials Processing Technology [IF: However, the addition of Ag also resulted in Cu-rich phases to precipitate at the grain boundaries of the as-cast material.